Maxtor free download - Maxtor OneTouch, Maxtor OneTouch III, Maxtor OneTouch II, and many more programs. Jan 13, 2020 Once the software is installed, Maxtor Quick Start will start locating Shared Storage drives on the Network. When your Shared Storage Drive is found, you will see its Network ID number and IP address appear in a drop-down menu in the middle of the screen.
Get a data lifeguard for Mac
Disk Drill brings deleted files back from the dead.
Most of the time, when you connect an external hard drive to your Mac’s USB port, you soon see it mount on the desktop. Apple likes to ensure these are easy to find, so they also appear in the Finder in the left-hand column under Devices, since Mac’s treat them the same way as another computer.
However, sometimes, an external hard drive doesn't show up. It’s annoying, especially when you need to transfer something right then. And besides, there can be a risk that data on the external USB pen, hard, or flash drive is corrupt, which means you can’t transfer what you need between devices at all.
Corrupt data can be one reason your Mac won't recognize an external drive, but there are other reasons too. Let’s take a look why this is happening and how you can get an external drive to appear on your Mac and get recover data to access to your documents.
How to fix an external disk drive that won't show up on a Mac
Why an external disk drive is not showing up? There could be a few reasons why a USB flash drive isn’t making an appearance.
Open an External Drive Not Showing on Mac
Get a huge set of top utilities for troubleshooting external hard drives not mounting on a Mac
Start with the basics:
- Check whether the drive is properly plugged in. It sounds obvious, but since this relies on a wire - either a USB cable or HDMI cable - if it’s not connected properly then it won’t appear on your desktop.
- Faulty cable. Assuming it’s plugged in correctly, not wobbly or loose, the cable could be at fault. Try connecting the same device with a different cable.
- Damaged USB or flash drive port. It could be a hardware issue with the Mac. If you’ve got another port, try connecting the device to that one.
- Reboot your Mac. Sometimes, if a USB disk won't boot, the cause is macOS issue. Hopefully, some data damage that can be fixed by restarting. Choose the Apple menu > Restart. Or press and hold the power button and, when a dialog box appears, click the Restart or press R. Restarting your Mac essentially clears your macOS’s memory and starts it up fresh.
- Incorrectly formatted drive. Not every external drive is optimized for Macs. It could be that you are trying to connect something only fit to interact with Windows devices. If you’ve got a PC or laptop, it’s worth connecting and seeing if you can access the files through another device. The best way to look for an incorrectly formatted drive is to go to
Apple (in the top toolbar menu) > About This Mac > Storage.
See if the external drive shows up here. For more information, go to the same menu option, then select System Report. - Mac not formatted to display external drives on the desktop. It could be that your Mac already recognizes the device, but just isn’t showing its icon on the desktop screen. Even if that is the case, the drive will still appear in the left-hand column of the Finder menu under Devices. You should be able to access your drive that way, and, in the Finder menu under Preferences > General, you can check External Drives to ensure that from now on it shows up on your desktop too.
- Reset NVRAM. To do this, shut down or restart your Mac, switch it back on and immediately press these four keys together for at least 20 seconds: Option, Command, P, and R. It should look as though your Mac has started again; if it has, release the keys when you hear the second startup chime. Hopefully, the hard drive has shown up now.
- Check Apple’s Disk Utility to see if an external drive is showing up. Disk Utility is within System Preferences, or you can find it using Spotlight. If it is visible, then click the option to Mount, which should make it visible on the desktop and in the External Drives option in the Finder menu.
Unfortunately, if none of those options has worked and the external drive still isn’t visible, then it could have crashed, or be well and truly broken. But there might still be a way you can recover the data on the external drive.
How to show connected devices in Finder
- Go to the Finder menu and select Preferences (Cmd+comma).
- From General tab tick External disks to ensure that from now on it shows on the desktop.
In the Sidebar tab you can choose which folders and devices will be shown in the left-hand column of the Finder window.
How to add cloud storages to Finder
You can also mount cloud storage as local drive on your Mac. By connecting Google Drive, Dropbox, or Amazon to your computer, you get more space for securely accessing and sharing files. For your ease, add cloud drives to Finder with CloudMounter app, so that you keep them close at hand. You can read detailed instructions on managing cloud storage as local drives here.
Repair the failed external drives with First Aid
If your drive is having problems, you can try to fix them yourself with First Aid and therefore get access to your files. First Aid tool will check the disk for errors and then attempt a repair as needed. It helps to verify and repair a range of issues related to startup HD and external drive problems. If you are able to fix the hard drive or SSD in your Mac (or an external drive) using Disk Utility you will hopefully be able to recover your files.
To run Fist Aid on an external hard drive:
- Open Disk Utility. You can searching for it using Spotlight Search or via Finder > Application > Utility
- Check on your external hard drive, click the First Aid tab and select Run to start running diagnostics.
If First Aid successful in fixing errors, the external drive should be available to mount. If the utility unable to repair issues, your drive truly is broken or formatted using a file system that the Mac cannot read - in this way we suggest you follow the next steps to recover data from a damaged disk drive.
How to recover data from a crashed drive
Thankfully, there is an app for that. Disk Drill is the world’s premier data recovery software for Mac OS X. Powerful enough to retrieve long-lost, mistakenly deleted files from Macs, external hard drives and USB drives and camera cards.
Get a file recovery app
With Setapp you get a pack of professional tools for file recovery and Mac maintenance.
An easy way to recover lost files on an external hard drive
Providing you already have Disk Drill Pro version, which you can get automatically by downloading from Setapp:
- Connect your drive to the Mac.
- Quit all other applications on the Mac, especially those that may be trying to access the external drive (e.g. iPhoto, Words)
- Launch Disk Drill.
- Click on the external drive that you are trying to recover files from. If it has partitions, you will see all of them. If, however, you still don’t see any volume to the external drive then you may need to try some of the steps above again or read the Disk Drill Scanning FAQs.
- To avoid the external drive being accessed during the recovery process, click Extras next to the drive or drive partition or file, then select Remount Volume As Read Only. A padlock will appear, protecting the drive during the process.
- Now click Rebuild (or Recover) next to the file(s) you are trying to recover. Once the scan is finished - it may take some time if the files are large - a list of files will appeal.
- Next, click Mount Found Items as Disk button on the bottom-left below the scan results.
- Disk Drill “strongly suggest saving the files to a different drive than the one you are trying to recover files from. Saving to the same drive substantially lowers your chances of recovery.”
- A drive icon will appear, which once you double click will give you the option to open the files as you would do before they were lost. Drag them to another location, such as your desktop or a folder on your Mac.
- Open the files to ensure they have been recovered properly and safely eject the external drive.
Disk Drill does have other ways to recover lost files but assuming there aren’t complications, this method is the most effective. Disk Drill Pro recovery app is available from Setapp, along with dozens of Mac apps that will make your life easier. Never have to worry about a crashed or corrupted external drive again.
A few more tips on getting your files back
- Macs and third-party apps that look after Macs, such as Disk Drill and iStat Menus come with a S.M.A.R.T. (also known as Self-Monitoring, Analysis and Reporting Technology) status monitor. If a SMART check reports errors, then it could mean the hard drive is at risk of failing completely. Within Disk Utility and Disk Drill, there are several solutions for this: Repair Disk Permissions and Repair Disk. If neither work, it’s recommended that you backup all of the data from the disk, erase, then run a SMART check again. The external hard drive should show up as Verified.
- Partitions can get lost within hard drives, temporarily hiding all of the information contained within. Disk Drill can help to identify and restore this information.
- Within Disk Drill, you can restore data when a hard drive is damaged or add formatting, which is also something Disk Utility can help with.
- CleanMyMac, another useful app available from Setapp, can help you identify external hard drive errors and repair them. It is an essential tool worth trying when you’re having external hard drive difficulties.
Try all these apps for free
Get a huge set of top apps for keeping your Mac in shape. Best utilities in one pack, give it a go!
Alternative ways to recover data from an external hard drive
Reset the System Management Controller (SMC) if your Mac shuts down when you plug in an external hard drive. Then use a different port to connect the external hard drive. If you’ve got a battery that you can’t remove:
- Shut down and unplug the power adapter
- Press Shift-Control-Option and the power button at the same time. Do this for 10 seconds
- Release all keys
- Plug the power adapter back in and switch your Mac back on
For Macs with removable batteries, you need to switch them off, remove the battery, then press and hold the power button for 5 seconds. After that, put the battery back in, plug in the power adapter and switch the power on again.
What’s your file format? One reason your Mac isn’t recognizing the hard drive is the file format. Windows uses NTFS file formats, while Macs, up until the introduction of Sierra, have used HFS+. Now, Apple has introduced the Apple File System (APFS) for newer operating systems. It is possible to format a hard drive so it can be read on Mac and Windows computers, providing you format using exFAT. However, if you’re having problems accessing the files and the issue is due to formatting, you will need to connect it to a device it can be read on, and then format the files correctly for the computer you are going to use it on next.
How to make Ext2/Ext3 drives readable on Mac
The common issue is Ext2- and Ext3-formatted drives are not readable on macOS. There are two ways to access such external drives on your Mac – via Linux OS or FUSE system. The easiest would be installing Linux to a secondary drive or virtual machine.
If you go with Linux installation, dual boot your Mac with Linux on another drive and use FAT32 as a transfer intermediary. If you don’t have a drive to install Linux to, use virtual machine as an interface for it. Transferring can be done the same way – with FAT32, or via network.
Another option for reading Ext2/Ext3 disks is mounting disk with Filesystem in Userspace (FUSE). Basically, it works as an extra interface enabling file system access via specially installed modules. Here’s how to mount drives with FUSE:
- Install FUSE for macOS or MacFUSE as well as fuse-ext2 module.
- Use the following Terminal command to enable Disk Utility’s debug menu and see all partitions: defaults write com.apple.DiskUtility DUDebugMenuEnabled 1
- Attach your Ext2/Ext3 drive and locate the device name via Disk Utility.
- In your user account, create a folder to be used as a mount point.
- Use the following Terminal command to mount the drive as read-only: fuse-ext2 /dev/disk2s2 /Volumes/mountpoint
- For write support, use the command: fuse-ext2 -o force /dev/disk2s2 /Volumes/mountpoint
And that’s not the only case where Terminal helps you access external drive.
Employ the handy all-powerful Terminal, which always comes forward with solutions for difficult problems. Especially if System Information does recognize the USB or hard drive, but continues to hide it from you, disconnect the drive and try to find it using the Terminal, which you can find in Applications > Utilities.
- Once in the Terminal, type in the command diskutil list
- A list with information about volumes and drives should appear
- Look for a section labelled /dev/disk_ (external, physical)
- Make a note of the whole line after the word disk
- Now put the following command into the Terminal diskutil info disk followed by the number or digits assigned to that disk
- Now you should see detailed information about the drive, therefore confirming that your Mac can and does recognize it
- Eject using the Terminal by entering the command diskutil eject disk followed by the number or digits assigned to that disk
- Physically remove the disk from you Mac
- Plug it back in and your Mac should recognize it
Console is also reliable when it comes to solving tricky problems, although it isn’t always that easy to use. You can find Console under Applications > Utilities > Console. Console shows if an external drive or any error is detected under the Errors and Faults tab. If no errors show up, then the problem is not caused by the device.
To sum up, there are lots of potential solutions for a Mac not reading an external hard drive. If we were to pick one, Disk Drill seems to be the most well-rounded, offering plenty of customizations and power in an easy-to-use interface. Disk Drill Pro recovery app is available via Setapp, along with 150+ Mac apps that strive to make your life much much easier. At the very least, you’ll never have to worry about a crashed or corrupted external drive ever again.
Seagate Shared Storage II network drive
Company: Seagate
Price: $499
http://www.maxstore.com/product.asp?sku=3338670
(1 TB version reviewed)
Nowadays, people have more networked computers in their homes and small offices, so the need for backing up all their files has become far more important. Add in the increasing file size of photographs and video files, and you’ll want a “network attached storage” device. NAS is the acronym of choice for these gadgets.
NAS devices are hard drives that can be accessed over a Local Area Network (LAN), to eliminate the problem of having to move hard drives from one computer to another, or to have a separate hard drive dedicated to backup for each computer. The NAS can have accounts for individual users, or the files can be open to all.
Seagate (formerly Maxtor) loaned a 1 terabyte Shared Storage II to the Weeks Division of MyMac Labs.
Let’s see how the Shared Storage II (SSII) fared in Weeks’ very small office setup of a Mac Pro, a MacBook Pro, and an old beater Gateway PC.
First impressions:
How big is a terabyte? It’s 1024 Gigabytes or 2^40 Bytes. I can’t count that high.
The unit is solidly constructed; it more resembles an aluminum ingot than a network storage device. This case will be able to take any and all abuse you can possibly dish out. Fellow reviewer John Nemo will chime in with his own comments below.
It’s not too big and not too small: 5.4 x 3.9 x 8.5 inches (136 x 97.5 x 217mm), and it tips the scales at 6 lbs.
The unit contains two 500GB drives, spinning at 7200 RPM, with 16 MB of cache. You can use the SSII as two 500 GB drives, or as one 1 GB drive.
For network connectivity, $499 dollars gets you:
1 – 10/100/1000 RJ-45 Gigabit Ethernet port 2 – USB 2.0 ports for printer sharing, storage, expansion or offsite data rotation
Once unpacked and cabled up, we ran the Maxtor EasyManage software from the installer CD. It installs the software itself, as well as a kernel extension that allows you to have the host computer wake from either sleep or shutdown to run unattended backups. A restart is required to take advantage of the wakeup features.
Setup involves creating either private or public accounts. Public accounts allow access to anyone, and private accounts are user specific. I used a public account for testing, as this is how many SOHO users would configure the drive.
Network volumes do not automatically mount when you boot your Mac or log in, but EasyManage can be set to auto mount a volume. If you wish to manually mount a volume on the desktop, you need to use the EasyManage software. I found EasyManage less than intuitive. The user interface requires too much pointing and clicking, and it’s not obvious to figure out how to mount a volume on the Desktop. Easy Manage also uses your web browser, not EasyManage itself, to setup, configure and test the SSII unit. It proved to be Safari-compatible, which was a plus.
Once you have setup your accounts, public or private, you can configure EasyManage with your backup choices. You can choose which drives or folder to backup and how often. One nice EasyManage feature is the ability to keep up to ten earlier versions of files, to establish a version history.
Automated backups can be set for a given time and day of the week. Manual backups can be done at any time.
Advanced options include waking the Mac from sleep, and starting from a shutdown state. You can choose to have the Mac shutdown after the backup is completed.
Once you’ve waded through EasyManage’s confusing interface, and have configured your backup, you’re ready to have the SSII get to work.
Here’s where the SSII proves to be Mac-unfriendly.
The SSII’s network volumes are accessed via a Windows file sharing protocol named CIFS (Common Internet File System). Mac OS X is fully capable of reading and writing via CIFS.
![Mac Software For Maxtor Shared Storage Drive Mac Software For Maxtor Shared Storage Drive](/uploads/1/2/6/3/126361773/320435308.jpg)
One of the nice things about the Mac is its ability to have long, descriptive filenames. The only character that’s not allowed under OS X is a colon (:).
The hitch with SSII, and it’s so big that it’s a deal-breaker for me, is that the CIFS protocol does not permit filenames to be longer than 31 characters, nor does it permit filenames to use many characters that are allowed in the Macintosh world. For example, you cannot have filenames containing ? [ ] / = + < > : ; ” , * |. Nor can the name be longer than 31 characters, even if they are all legal.
So, EasyManage will be merrily copying files, then will rudely interrupt you with an error dialog box saying “the file was not copied – there may be an invalid character” (that is, /|:*?<>) in the file or folder name.
You have the option of skipping this file or folder, or skipping ALL files/folders with these characters.
The other problematic error message is: Bad Filename: This may be because the destination disk doesn’t allow names longer than 31 characters.
Again, you can skip the offending file/folder, or skip them all.
In my first full backup, I had well over a hundred files that could not be copied. If I elected to “Skip all” I would have no idea of which files were not copied. If I watched the backup to note individual files with illegal filenames, I’d be watching for hours.
As a Macintosh user, this limitation is unacceptable. I realize it’s a fundamental part of CIFS, but I’m not willing to use tools like “A Better Finder Rename” to change my filenames to make them Windows-compatible. I LIKE my Mac filenames, and don’t want to change them.
I did create a workaround, however. I created a disk image on my network volume with a Windows friendly filename. Next, I mounted the disk image, and copied all my files into the disk image. I used both the Finder, as well as Synchronize Pro. Using a Macintosh disk image avoids any problems with illegal characters, but it also prevents you from using the automated backup capabilities of EasyManage. I did it to see if it would work; it’s not practicable on a day-to-day basis.
The other deal breaker for me was slow copying speed. While the SSII has Gigabit Ethernet, the overhead associated with CIFS takes a terrible toll on copy performance. I can copy files between my Mac Pro and MacBook Pro at speeds averaging 25 MB/sec for large files. The SSII never managed more than 15, and usually transferred the same large files at about 10 MB/sec. Small files always copy more slowly, even in the Mac world, but the SSII copy speed was far slower than my Mac Pro to MacBook Pro copy speed.
It’s too bad that the SSII has the CIFS filename limitations, and slow read/write speeds, as it has plenty of good features.
I used the shared media feature to run both my iPhoto library and iTunes library from the SSII. I was able to stream music to my SliMP3 (http://www.slimdevices.com) with no trouble, and sharing the iPhoto library to both wired and wireless Macs went with nary a snag.
I tested, albeit briefly, the wakeup and shutdown features for automated backup, and all worked flawlessly.
Additional comments by John Nemerovski:
Seagate Maxtor provided a second non-working SSII drive to MyMac.com, giving me permission to take it apart and examine its internal organs. Not being an engineer or supergeek, I used a small screwdriver to remove screws and a large screwdriver to pry the case open. Do NOT try this at home or office. It will void your warranty and ruin your expensive unit.
After fifteen minutes, the components were divided into uneven piles, for: the metal casing, lightweight, stylish, and strong; blue rubber gaskets that held everything very snugly in place; the aforementioned screws; a small but impressive circuit board, power supply, and fan; a bunch of miscellaneous wires, tape, and assorted thingamabobs; and two beautiful 500GB high speed SATA drives.
Maxtor Shared Storage Ii Manual
I was impressed with how well everything had fit together, sleek and strong, and how much inherent hardware value the company provided for $500. David and I have had similar mixed results with Maxtor’s software in the past, and we urge them to develop more Mac-friendly utilites in the future.
Conclusion:
The Seagate Shared Storage II is a splendid unit for PC users, but it is not well suited for day-to-day Macintosh usage. The CIFS limits on filenames prevent many Mac files from being copied to the shared drive. Copy speed is far slower than Gigabit copies from Macintosh to Macintosh. The EasyManage software, while fully featured, is somewhat confusing. The Shared Storage II does work well as a shared media server, assuming all the medeveia filenames are CIFS-compatible.
The Seagate Shared Storage II is a splendid unit for PC users, but it is not well suited for day-to-day Macintosh usage. The CIFS limits on filenames prevent many Mac files from being copied to the shared drive. Copy speed is far slower than Gigabit copies from Macintosh to Macintosh. The EasyManage software, while fully featured, is somewhat confusing. The Shared Storage II does work well as a shared media server, assuming all the medeveia filenames are CIFS-compatible.